HVAC Supplies - Page 771

Manufacturer: HVAC Premium Brand: HVAC Premium Color: Black

14" X 20 Steel Return Air Filter Grille for 1" Filter - Removable Face/Door - HVAC DUCT COVER - Flat Stamped Face - Black14"w X 20"h Is The Size For The Duct Opening Measurement Only, Actual Front End Outer Dimensions Are 16.5" Width X 22.5" Height - SEE BELOW IN DESCRIPTION HOW TO MEASURE A GRILLEWhy BLACK? Simple, Because Black Grilles Always Look Sharp And Never Show Dirt & Dust MarksYou may think of grilles and registers as a generic component of the ventilation system in your house. But they are also the most visible representation of you air system. These grilles and registers give you an extra measure of quality that are visible to your family members and house guests. High Standard Every part is hand inspected for quality before it is packaged, no exceptions. No Sharp Surface Edges. Just run your finger along the edge of the top plate and you will find a smooth finished surface. Powder-Coat Finish - Smooth, Shiny, Scratch-Resistant, Beautiful. Quality Packaging - Carefully Shrink Wrapped With Cardboard Backing To Prevent Damage In Shipment Easy Unrestricted Air Flow For Your HVAC System This model has ½" fin design This model can have the face/door removed. This model uses a 1" thick filter. How To Measure A Grille Overall Size: Measure the size of the air duct/drywall opening. Do not measure the overall size of the register itself, only measure the "hole" in the wall/duct. Every grille has a front end frame, that will overlap at wall joint. Total outer size of this grille is; listed size +2.5". Width vs Height The first number in a grille size, represents the width, the second number represents the height. Example: If your hole is 20" wide by 14" tall, order a 20x14. If your hole is 14" wide by 20" tall, order a 14x20.

Manufacturer: Clear the air Brand: Clear the air

Clear The Air Merv 8 filters effectively remove 85% of airborne particles. Our Merv 8 filter eliminates allergens such as dust, pollen, mold spores, and pet dander. Our advanced pleat technology provides less air flow resistance, with higher efficiency. Our Merv 8 standard capacity pleated filters are offered in ASHRAE 52.1 and 52.2 (MERV) ratings and are built to withstand rigorous conditions. Clear the air Merv 8 filters are available in 47 sizes so you are sure to find what you are looking for. Clear The Air Merv 8 Pleated Filters are available in 1", 2" and 4" depth. The electrostatically charged 100% synthetic graduated density media is continuously bonded to a 30 gauge galvanized, corrosion resistant, expanded metal support grid with an effective open area of 96%. The media is resistant to a wide range of chemicals, does not absorb moisture and will not support microbial growth. The controlled pleat spacing maximizes surface area and dust holding capacity and is bonded to the enclosure frame to prevent dust bypass. The enclosure frame is constructed of high wet strength moisture resistant beverage board. The diagonal support members of the frame are bonded to the entering and exiting apexes of each pleat to prevent pleat collapse and filter bowing.

Manufacturer: Metal-Fab/Air-Craft Brand: Metal-Fab/Air-Craft Color: White

30" X 18 Steel Return Air Filter Grille for 1" Filter - Removable Face/Door - HVAC DUCT COVER - Flat Stamped Face - White30"w X 18"h Is The Size For The Duct Opening Measurement Only, Actual Front End Outer Dimensions Are 32.5" Width X 20.5" Height - SEE BELOW IN DESCRIPTION HOW TO MEASURE A GRILLEYou may think of grilles and registers as a generic component of the ventilation system in your house. But they are also the most visible representation of you air system. These grilles and registers give you an extra measure of quality that are visible to your family members and house guests. High Standard Every part is hand inspected for quality before it is packaged, no exceptions. No Sharp Surface Edges. Just run your finger along the edge of the top plate and you will find a smooth finished surface. Powder-Coat Finish - Smooth, Shiny, Scratch-Resistant, Beautiful. Quality Packaging - Carefully Shrink Wrapped With Cardboard Backing To Prevent Damage In Shipment Easy Unrestricted Air Flow For Your HVAC System This model has ½" fin design This model can have the face/door removed. This model uses a 1" thick filter. How To Measure A Grille Overall Size: Measure the size of the air duct/drywall opening. Do not measure the overall size of the register itself, only measure the "hole" in the wall/duct. Every grille has a front end frame, that will overlap at wall joint. Total outer size of this grille is; listed size +2.5". Width vs Height The first number in a grille size, represents the width, the second number represents the height. Example: If your hole is 20" wide by 14" tall, order a 20x14. If your hole is 14" wide by 20" tall, order a 14x20.

Manufacturer: SunTouch Brand: SunTouch

The SunStat 500710 is a Basic Non Programmable Control used to control the floor temperature of a SunTouch electric floor heating system. This simple control is easy to install and has a built in GFCI and 15 amp relay so you can control up to 150 sq. ft. of 120V or 300 sq. ft. of 240V SunTouch mats. Senses the FLOOR Temperature Using the INCLUDED 15 ft floor Sensor Wire and has Built in Ground Fault Protection with no need for an additional GFCI circuit in most areas. Large temperature setting dial and 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control 300 SF of 240v mats. No Programming necessary. Simple & Easy to operate with 1 Year Factory Warranty. On Off switch is located on side of control as is the GFCI Test button.

Manufacturer: ROBERTSHAW Brand: Robertshaw

' Gas Cooking Control, Thermostat Kit For Ovens, Gas Type NG/LP, Gas Connection 1/4 In, Dial Range 250 to 550, Temp. Range 250 to 550, Bulb Size 3/16 In X 11 -3/16 In, Capillary Length 48 In, Mounting Position 4 Way, For Use With Commercial Cooking Applications, Replaces BJ and BIWA, Includes Dial, Installation Hardware '

Manufacturer: bullet tools Brand: Bullet Tools Model: 701AF

Convert your Bullet Tools Magnum Shear into an angle cutting animal with this premium accessory.

Manufacturer: TruAire Brand: Truaire Model: 170 36X12

36"w X 12"h Steel Return Air Grilles - Sidewall and Cieling - HVAC DUCT COVER - White36"w X 12"h Is The Size For The Duct Opening Measurement Only, Actual Front End Outer Dimensions Are 37.75" Width X "w X 13.75" Height - SEE BELOW IN DESCRIPTION HOW TO MEASURE A GRILLEYou may think of grilles and registers as a generic component of the ventilation system in your house. But they are also the most visible representation of you air system. These grilles and registers give you an extra measure of quality that are visible to your family members and house guests. Some of the best features aren't readily apparent, but you will appreciate the benefits over the period of time. This grille has a high standard of design, production and finish on all products. Every part is hand inspected for quality before it is packaged, no exceptions. No Sharp Surface Edges. Just run your finger along the edge of the top plate and you will find a smooth finished surface. Powder-Coat Finish - Smooth, Shiny, Scratch-Resistant, Beautiful. Looks Like It Was Just Waxed Quality Packaging - Carefully Shrink Wrapped With Cardboard Backing To Prevent Damage In Shipment Easy Unrestricted Air Flow. How To Measure A Grille Overall Size: Measure the size of the air duct/drywall opening. Do not measure the overall size of the register itself, only measure the "hole" in the wall/duct. Every grille has a front end frame, that will overlap at wall joint. Total outer size of this grille is; listed size +1.75". Width vs Height The first number in a grille size, represents the width, the second number represents the height. Example: If your hole is 20" wide by 14" tall, order a 20x14. If your hole is 14" wide by 20" tall, order a 14x20.

Manufacturer: Decor Grates Brand: Decor Grates Model: AJH614-NKL Color: Brushed Nickel Finish

Decor Grates floor registers are built with the finest materials. Each and every register goes through a quality assurance process to ensure your satisfaction. Our classic designs will enhance any rooms decor and give you years of trouble free operation. Our family owned company takes great pride in making sure you are totally satisfied with your purchase.

Manufacturer: Goodman Brand: OEM Replm for Goodman

This is a Brand New OEM Replacement Transformer

Manufacturer: DuraTech Brand: Duratech

An Attic Insulation Shield is required for installations that pass through an attic to prevent insulation and debris from accumulating near the chimney. The Attic Insulation Shield fits over the Firestop Radiation Shield or a support box and consists of two-parts - a collar and a base. Comes with a mesh sleeve around the top. DuraTech is a double-wall, all-fuel chimney system for use with wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas, and zero-clearance fireplaces that are factory-built.